However, this is not a traditional SPAC deal. PSTH has taken those funds and agreed to buy a 10% stake in Universal Music Group for $4 billion, giving the record label an enterprise valuation of EUR35 billion. In fact, Pershing Square Tontine, also known as PSTH, is the biggest SPAC to have ever-listed, having raised $4 billion at $20 per share when it went public in July 2020. These are also known as blank-cheque companies that list on an exchange and raise money from investors so they can buy an existing business that wants to go public but avoid a traditional initial public offering. Pershing Square Tontine is a Special Purpose Acquisition Company, better known as a SPAC. * Debug probe connector: Samtec only has cable assemblies.Pershing Square Tontine to buy 10% stake in Universal Music * Board header: () (unshrouded) and () (shrouded, but no guide pin)įeatures 2 rows of 5 pins each, 0.05" (1.27mm) pin and row pitch. * Board header: () (straight angle) or () (right angle) * Debug probe connector: Samtec only has cable assemblies. * Debug probe connector: ()įeatures 2 rows of 10 pins each, 0.05" (1.27mm) pin and row pitch. * Board header: () (SMT - surface mount) and () (TH - through hole) - both models have no guide pinsįeatures 2 rows of 10 pins each, 0.05" (1.27mm) pin pitch, 0.10" (2.54mm) row pitch. * Debug probe connector: () (with strain relief) and () (without strain relief) * Board header: () (unshrouded, through hole), () (unshrouded, surface mount), () (shrouded, through hole) IMPORTANT! The part numbers below are based on the manufacturers' specifications, which can change without prior notice. The use of ARM headers causes loss of features as no EMU0/1 pins are present ġ These devices support CTools MIPI System Trace (STM) and core tracing or ARM ETM/TPIU core tracing to the pinsĢ These devices support CTools MIPI System Trace (STM) but NOT core tracing or ARM ETM/TPIU core tracing to the external pinsģ These devices have one or multiple ARM CPUs, but do not support MIPI System Trace (STM), core tracing, or ARM ETM/TPIU core tracing to the external pinsįeatures 2 rows of 7 pins each, 0.10" (2.54mm) pin and row pitch. Use a 20 pin ARM header if compatibility with ARM tools is desired Sitara (AM170x, AM180x, AM35x, AM37x) / OMAPL / OMAP / Davinci3 Use the 60 pin MIPI connector if it is desired to keep compatiblity with devices which support Core tracing/ETM+TPIU Use the 20 pin TI header for maximum MIPI STM trace performance. ARM 34 pin Mictor only recommended when XDS support is not needed and compatiblity with ARM tools is required.
60 pin MIPI connector recommended to support both MIPI STM and core tracing. Sitara (AM4x, AM5x) / Keystone I (C66x) / Keystone II (66AK2)1 Use the ARM Header if compatibility with ARM tools is desired. # Types of JTAG headers per device family For target mechanical requirements that could impact device heights in proximity to the emulation header on your board and possible keep-out areas required for good connection and room to disconnect the cable connector, see your XDS manufacturer's documentation. Target cable design and connectors vary between XDS manufacturers. For part numbers, check the next section. For part numbers, check the next section.ģ0.05" (1.27mm) pin and row pitch. For part numbers, check the next section.Ģ0.05" (1.27mm) pin pitch, 0.10" (2.54mm) row pitch.
* For ARM connectors, see ()ġ0.10" (2.54mm) pin and row pitch. * For MSP430 see (./files/JTAG_MSP430_legacy.pdf) for details. * For the TI 60 pin connector and the MIPI 60 pin connector, please check the (). * Part numbers for connectors and headers are at the bottom of the table and at section (#connector-information). * For Trace, you may also want to consider reading () * The document () describes the 14-pin JTAG connector and target board electrical requirements for XDS510 JTAG support (despite it's title it is not specific to the TMS320C6000 DSP).
This page covers in detail several aspects to properly identify, specify and use these different standards. Texas Instruments supports a variety of JTAG connection methods to both its development kits and custom boards.